• How To Install Electrical Conduit Outdoors Project Guide

The plastic on Schedule 80 is thicker, but the conduit has the same outside diameter as 40, so the inside diameter is smaller. Always install Schedule 80 conduit. Single-gang electrical boxes will work, but if you have two or more conduit sections connecting to one box, buy double-gang. The male connectors on the ends.

As with any electrical project, every precaution should be taken to protect yourself and others from electrical shock; the most important precaution being to never work on live circuits. Ensure that the power is off before working on any electrical circuit! Refer to our on our website, and any other useful safe work practices resource at your disposal.

Any and all outdoor wiring codes must be followed, permits obtained, and inspections performed as required. There are two main categories that outdoor wiring installations could be classified as: 1. To provide a safe amount of light to traffic areas such as stairwells, steps, sidewalks, gates, outdoor cooking facilities, etc. Decorative: To illuminate and accent plants, trees, or shrubs, architectural features, artwork or pools and spas. Decorative lighting can also be functional. Cable and Conduit for Outdoor Wiring For outdoor and underground wiring, you can use cable suitable for exposure to the elements such as NMWU-90, or direct burial cable of the appropriate rating, conduit (both metal, plastic, or liquid-tite flexible conduit) and wire, or a combination of both. It is important to check both national and local code rules for outdoor wiring installation requirements.

How To Install Electrical Conduit Outdoors Project Guide

Ground Fault Circuit Protection for Outdoor Wiring Ground fault circuit protection is required for most outdoor electrical circuits so again, check with the local electrical authority for the requirements for your particular outdoor wiring project. All outdoor electrical fittings and device boxes must be rated for outdoor use, installed with supplied gaskets and appropriate entrance fittings. Outdoor Switches Switches used outdoors must be protected with weatherproof covers and gaskets to prevent exposure to the elements. Outdoor Light Fixtures All light fixtures installed outdoors must be rated for, and approved for outdoor installation, and all gaskets provided must be installed and maintained in good condition. Make sure that the bulbs are rated for outdoor use as well. Receptacles All receptacles and outlets must be rated for outdoor use and be fitted with the correct weatherproof cover plate and gaskets.

Check your local jurisdiction for the specific requirements for weatherproof cover plates for receptacles. The National Electrical Code mandates that all outdoor receptacles be fitted with an in use cover plate.

These devices provide protection for the outlet even when a cord is plugged into the outlet and are available in many styles. Not all areas have adopted all of, or even parts of the N.E.C., so again, it’s important to check with your local electrical authority. Make sure that you get the correct cover for the device box used, and that the cover provides protection for the orientation of the receptacle in either the vertical or horizontal position, whatever the case may be.

Connectors and Fittings All connectors and fitting must be approved for outdoor use and fitted with the supplied gaskets. Installing cable or conduit underground Before digging any holes or trenches, always check for any and all potential underground hazards such as electrical lines, gas lines, telephone lines, cable television lines, water or irrigation lines. Many areas provide underground line location services, and damaging any utility lines without calling for locating services can result in injury or death, and if you’re lucky, only liability for the damage caused. After all locates are complete, and a thorough investigation of any other potential underground hazards, carefully dig your trenches and holes, and hand expose any line crossings manually if using equipment such as trenching machines or backhoes. When planning your trenches, take care to follow as straight of a line as possible, and make your corners as smooth as possible with a wide radius on bends.

Check local code rules for the appropriate burial depth with consideration to what you are using, either conduit and wire, or underground cable, and whether under driveways or sidewalks, gardens, flower beds, or lawn. Summary Outdoor wiring projects are no more difficult for the DIYer than projects inside the home, as long as you use the correct materials, follow the rules, obtain the permits, and have the job inspected as required.

In this video, electrician Keith Diemer lights up a deck. Turn off the electricity at the main electrical panel, then use a hammer-drill and carbide-tipped masonry bit to bore down through the garage floor and into the crawl space. Position the hole alongside the main electrical panel. Pull plastic-sheathed electrical cable up from the crawl space and into the garage.

Attach metal conduit to the ceiling of the crawl space. Feed the cable through the conduit. Drill a hole through the exterior house wall and into the crawl space. Position the hole just below the deck. Pull the cable from inside the crawl space through the hole in the wall. Slide the cable into a length of flexible conduit. Pass the conduit through the hole in the house wall and into the crawl space.

Use a drill and hole saw to bore a hole down through the deck. From below the deck, push the flexible conduit with encased cable up through the hole in the deck. Attach a watertight cable connector to the end of the flexible conduit and to a watertight electrical box. Slide the box down onto the end of the conduit.

Join together the two watertight connectors by tightening the threaded nut. Use the hammer-drill to bore holes in the brick wall, then tap in plastic wall anchors. Fasten the electrical box to the wall by driving screws into the anchors.

Strip the insulation from the end of the cable and attach the bare copper wire to the green grounding screw inside the box. Make the wire connections between the cable and a GFCI outlet. Screw the outlet to the box, then apply a bead of silicone around the face of the box. Screw on the box cover. From inside the garage, install a cable connector onto the main electrical box.

Pass the cable end through the connector, then tighten the connector. Make the wire connections between the cable and the electrical panel, then install a 20-amp circuit breaker. Connect the black cable wire to the circuit breaker.

Download indigo renderer plugin check. Turn the power back on and test your work.